Trane XR14 Central Air Conditioner
Updated: Sep 5, 2016Write a review
Read more about Trane Central Air Conditioners
Overview of the XR14
The Trane XR14 is a single-stage air conditioner with an efficiency rating of up to 16 SEER. It has a Climatuff compressor and an all-aluminum spine fin coil, and DuraTuff non-corrosive base pan that won't warp, crack or rust. A compressor sound insulator on select models helps keep sound levels as low as 72 decibels. Galvanized steel louvered panels help protect the unit from the elements, while WeatherGuard fasteners and a powder paint finish help resist rust and corrosion.
Date created: 2016-09-05
Name: Vance K.
Location: League City, TX
I was working in the garage and heard a loud hissing noise like a sprinkler head blew off. It was dusk so I knew the sprinklers weren't on. I followed the sound to the AC condenser and I see sparks flying out the top of the condenser unit. Looking into the unit, the plug to the compressor is on the pan floor and kinda burnt looking and the Freon is blasting out of where it was plugged in. The AC is only three years old.
Date created: 2016-01-18
Name: K. Wilson
"Have high expectations for this unit"
Bought this unit in April 2015 to replace a 20-year-old Lennox system. The Lennox, in the last 5 years of owning it, needed capacitors, a fan motor, a control board and leaks patched in the evaporator. After spending $700 in repairs I wasn't going to spend another $1,000 on a new evaporator and more expensive R22. I don't have complaints about the Lennox, I think I got more than my money's worth on it. My HVAC guy put in the Lennox and I would have gone with another one (glad I didn't) but he no longer sells that brand. He sells Armstrong Air and Trane now. I really wasn't hung up on a particular brand but I didn't know anything about Armstrong Air so I went with Trane. Couldn't be happier with my decision. The Trane XR14 combined with the all aluminum evaporator and the XV80 furnace work flawlessly. My old Lennox was mostly trouble free for 15 years and worked well but not like the Trane. Although they are both 3.5 ton units the Lennox would run non-stop from noon until sundown to maintain 75 during the hottest part of summer. When it got really hot (>100) and humid it couldn't maintain 75 and the temperature would go up to 78-80 degrees. It has always been like this even when it was brand new. The Trane has no trouble maintaining 75 even when the outside temperature is over 100. Even on those days it cycles about twice an hour and doesn't run non-stop. Trane is not kidding when they say their all-aluminum coil is better at heat transfer than traditional aluminum fin copper tubing condensers. Even though it's only 1 year old it has worked flawlessly since it's first start up. I think most people who have problems with a new system of any brand are not matching all the components and getting a bad install. When I bought the Lennox it was to replace a Carrier condenser that needed 2 compressors and numerous repairs in 10 years and never cooled well. The A/C guy I hired to replace the Carrier said that it was slightly undersized at 3 tons but most of the problems I was having was that it was a new condenser connected to a 14 year old Fedders evaporator and furnace. Nothing was wrong with Carrier as a brand. He stressed you should always match the condenser with a new evaporator and air handler/furnace. Saving money by keeping your old furnace/air handler because it's working fine will cost you dearly down the road. Rheem, Carrier, Trane, Goodman etc. engineer and test their equipment to work with their own evaporators and air handlers. Putting your brand new Trane A/C with your old Carrier air handler will probably cause problems. For example, he said Trane evaporators are taller than evaporators from most other brands and Trane only makes 1 type of A coil. Some installers will put in a different brand or a N coil if there is a problem with clearance instead of redoing the plenum to fit the Trane evaporator. Something this minor could cause problems a few years down the road.
Date created: 2015-09-20
Name: Todd P.
Location: Rockledge, FL
"House's first system and lasted 12 years"
This unit was the one that came with the house and the air handler was a gas lower end model(in Florida you don't need heat other than the law requires you have it). This system ran flawlessly for almost 12 years, then the A-frame coil got a leak and with it being so old we decided to replace the system with a Tempstar, which was big mistake. The Tempstar is a high-end XTX+ SEER 19 system and has broken twice in the first 15 months of being installed! Tempstar/Carrier is junk, should have stayed with Trane when we bought a new one.
Date created: 2013-07-14
Name: Anthony Teets
Location: Lake Placid Florida
Unit was built 10/2006 and installed 8/2007. Big selling point was efficiency of variable speed motor in the air handler. On 7/13/2013, the motor was not running and I called Miller Air Conditioning Inc. that sold the unit to me and installed it in Lake Placid, Florida. I was informed that the motor was out of warranty and that a new one would cost over $1000.00. I replaced it with a single speed motor that cost $618.00 installed. I would not advise anyone to buy Trane products with such unreliability. The original cost of purchase and installation was over $5300.00.
Other XR14 Reviews
Most of the posts regarding the XR14 on sites such as doityourself.com have to do with minor problems like a faulty thermostat or problems due to poor installation, such as the homeowner whose unit was not cooling well due to the ducts not being properly insulated.
Trane XR14 Model Numbers
The XR14 is available in different models which vary in efficiency and capacity.
|Model Number||SEER||BTUs per Hour|
Product registration is required within 60 days of installation for maximum warranty coverage. The warranty for the Trane XR14 air conditioner is comprised of the following:
- 10-year limited warranty on the compressor
- 10-year limited warranty on the outdoor coil
- 10-year limited warranty on internal functioning parts
Labor costs are not covered by the warranty. Optional extended warranties which can pay for labor and other costs not covered by the manufacturer's warranty are available.